- Name: Industrial Desiccant Dehumidifier
- Dehumidifying Capacity: 13kg/h
- Process air flow: 2550m3/h
- Reactivation air flow: 925m3/h
- Voltage: 380V
- Current: 50A
- Power rating: 24KW Max power: 27KW
- Applied Temperature: -20°C-70°C
- Body: Stainless Steel
- Dimension: 1295*880*1300mm
- Applications: Used for drying basement, garage, cellar, crawl
space, small space
13kg/H Industrial Desiccant Rotor Dehumidifier For Warehouse
The RY-2500M desiccant dehumidifier is designed to efficiently
dehumidify in low moisture applications. Its airtight construction
delivers accurate conditions and optional features provide
versatility to adapt the system for specific applications.
The electrical control system conforms to EN 60204 (IEC204)
standards. The electrical components are mounted on busbars and are
constructed of halogen-free plastic. The electrical system is
designed for up to 400V and 70º C. MX Series dehumidifiers conform
to both harmonised European Standards
and to CE marking specifications.
Besides, RY-M rotor technology is the precision seals which divide
the air distribution chamber. These provide a precise airflow
balance for dehumidification and reactivation while allowing for
alternative fan placement and rotor sectioning.
RY-2500M series dehumidifiers conform to both harmonised European
Standards and to CE marking specifications.
Process air flow
Reactivation air flow
*Accurate camputer contral system
*Proflute Rotor, imported from Sweeden, washable
*Dehumidifies efficient down to -20 º C.
*High capacity with very low dewpoints.
*Reactivation heater choice
- electrical, steam or gas.
*Microprocessor based control or base control choice.
*Compact design - requires minimal floor area.
How Desiccant Dehumidification Works:
Desiccant dehumidifiers perform exceptionally well when used in
cooler climates, or when a low dewpoint, deep drying or low
humidity levels are required because they dehumidify through
adsorption. Since desiccant dehumidifiers do not produce water,
they will work effectively down to sub zero temperatures. Their
operation is simplistic yet extremely effective and reliable.
In a typical dry desiccant system, the desiccant is mounted on a
rotating wheel. As the wheel turns, the desiccant passes
alternately through the incoming process air where the moisture is
adsorbed and through a “regenerating” zone where the desiccant is
dried and the moisture expelled. The wheel continues to rotate and
the adsorbent process is repeated.
Typically, about three-fourths of the desiccant wheel is exposed to
the incoming air throughout the process. During regeneration, the
desiccant is heated by a direct-fired gas burner or indirect-fired
water or steam coil.
Process Inlet—Air to be dried. May be outside air, inside air or,
more commonly, a mixture of air with high humidity content.
Process Outlet—Air is dried by desiccant wheel. May be cooled,
filtered or otherwise handled. Relative humidity is substantially
lower and temperature slightly raised.
Reactivation Inlet—Air flow, usually outside air, that drives
moisture off wheel. Reactivation air is heated by direct-fired gas
burner or indirect-fired water or steam coils.
Reactivation Outlet—Hot, wet air from wheel is exhausted outside or
passed through an air-to-air heat exchanger. Using a heat exchanger
to preheat incoming process air offers substantial savings in
This’s designed for cold storage, warehouses, production facilities
etc. Regeneration by electricity, steam or gas.
Heat recovery system available for even higher efficiency.
Process air flow
Dry air flow
1.The product has three-year free warranty from the date of
2.The warranty shall not apply: (i) to any Product subjected to
accident, misuse, neglect, alteration, Acts of God, improper
handling, improper transport, improper use, improper testing or
unauthorized repair or (ii) to cosmetic problems or defects which
result from normal wear and tear under ordinary use, and do not
affect the performance or use of the Product.All warranties are
void if the product is opened, altered, and/or damaged.
3. CUSTOMER MUST PRESENT THE SALES INVOICE OR RECEIPT FOR FREE
4. Service Hotline: (86) 571-86817211-811 Fax Hotline:
IN NO EVENT SHALL OUR COMPANY OR THE SUPPLIER BE LIABLE TO YOU OR
ANY OTHER PARTY FOR ANY DIRECT INDIRECT GENERAL SPECIAL INCIDENTAL
CONSEQUENTIAL EXEMPLARY OR OTHER DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PRODUCT INCLUDING WITHOUT LIMITATION DAMAGES
FOR INJURY LOSS OF PROPERTY BUSINESS PROFITS BUSINESS INTERRUPTION
OR FROM ANY BREACH OF WARRANTY EVEN IF OUR COMPANY OR SUPPLIER HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO CASE SHALL
OUR COMPANY OR SUPPLIER S LIABILITY EXCEED THE AMOUNT YOU PAID FOR
Specifications designs and dimensions subject to change without